|
|
|
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This equipment has been tested and found to conform to the directives and standards for a Class A Information Technology Equipment TYPE and for the Commercial Light Industrial equipment class.
The VIP-808 "MegaTouch"™ Video with Touch Screen capabilities are available as an Integrated Video Switch with Remote Control, switching one video monitor with touch screen between eight PC's.
The "MegaTouch" system consists of the following components:
1. One - Video Switch Unit
2. One - VIP-210 Power Supply.
Note: The "MegaTouch" does not come with VGA or serial extension cables. They may be ordered from Vetra separately (see Accessories ).
There are two main steps to connect the Video Switch:
1. Connect PC's to Switch unit:
a) Connect the Video outputs of
the PC's to the Switch using 15 pin HDD15 male/female extension
cables. Connect PC#1's video output to the backpanel connector
of the Video Switch marked "TO PC1 VIDEO". Connect PC#2's
thru PC#8's video outputs to the backpanel connectors of the Video
Switch marked "TO PC2 VIDEO" thru "TO PC8 VIDEO".
b) Connect the Touch Screen inputs of the PC's to the Switch using
9 pin DB9 male/female extension cables. Connect PC#1's touch screen
input to the backpanel connector of the Switch marked "TO
PC1 T.S.". Connect PC#2's thru PC#8's touch screen inputs
to the backpanel connectors of the Switch marked "TO PC2
T.S." thru "TO PC8 T.S.".
2. Connect a Monitor(s) to the Switch:
a) Connect the VGA monitor to
the 15-pin HDD connector on the backpanel of the Video Switch
marked "MONITOR IN".
b) Connect the Touch Screen to the 9-pin DB9 connector on the
backpanel of the Switch marked "TOUCH SCREEN IN".
OPERATION
1. Power Up Sequence:
The switch derives its power from an external power supply provided with the MegaTouch. When the Video Switch is powered up, observe on the Video Switch that the front panel Led marked "PWR ON" comes on.
2. PC Selection:
a) Front Panel Selection:
b) Remote Control (available on all models):The MegaTouch may also be switched via remote control. A Hex 31 (PC #1), Hex 32 (PC #2), Hex 33 (PC #3), and Hex 34- 38 for PC's 4 - 8 sent via RS-232 to pin 2 of the DB-9 connector on the rear panel marked "REMOTE CONTROL" will switch the MegaTouch from PC1 thru PC8. The data format is one start bit, eight data bits, least significant bit first, one stop bit and no parity. the baud rate is 9600. Pin 5 is ground.
SPECIFICATIONS
Mechanical Dimensions
|
|
|
|
|
|
| VIP-808-V-TS |
|
|
|
|
| VIP-808-V-TS-DE |
|
|
|
|
Environmental Operating
Temp: 5
to 104 deg. F (-15 - 40 deg. C)
Storage
Temp: -4
to 122 deg. F (-20 - 50 deg. C)
Supported
Hardware Video Monitors: VGA,
SVGA
Maximum
Resolution: up to 1600 x 1200 to 75 Hz
MegaTouch is a trademark of
Vetra Systems Corporation Copyright © 2003 by Vetra Systems
Corporation All Rights Reserved
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
275-J Marcus Blvd. Hauppauge, NY 11787 USA Toll Free 1-800-537-9296 Tel: 631-434-3185 Fax: 631-434-3516 e-mail: sales@vetra.com |